Low power consumption/heat dispersion Marvell in build Copper RJ-45 SFP+ CAT.6a/CAT.7 Transceiver Module 30m

10G T to 10G T, 10G T to 5G T, 10G T to 2.5G T, 10G T to 1000M T SFP+

Tested in Targeted Switches for Superior Performance, Quality, and Reliability

Description:

This 10GBASE-T SFP+ Copper transceiver GTS-T0096-03 provides 10GBase-T throughput up to 30m over cat.6a/cat.7 copper cable via RJ-45 connector.

It is compliant with the Multi-Source Agreement (MSA) and 10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T standards as specified in IEEE STD 802.3an, 802.3ab and 802.3au. The 10G copper SFP+ transceiver allows IT designers and data center professionals to extend the distance of 10GbE Ethernet links over an existing copper cabling infrastructure. The copper module provides convenience, flexibility and cost savings for deploying 10Gb/s technology over balanced twisted-pair copper cabling.More importantly, the 10G RJ45 SFP+ transceiver automates interoperability with legacy Ethernet devices and backward compatible with legacy 1000Base-T networks.

Each SFP+ copper transceiver module is individually tested to be used on a series of switches, routers, servers, network interface card (NICs) etc. Featuring low power consumption, high bandwidth, this easy to install, hot swappable 10G SFP+ transceiver is ideal for enterprise networking for LAN applications and different other networking places using copper connections.

Functional Specification:

Features

• Link length up to 30m using Cat 6a/Cat 7 cable
• SFF-8431 and SFF-8432 MSA Compliant
• IEEE 802.3az and 802.3an Compliant
• IEEE 802.3bz for 5G&2.5G BASE-T
• Hot-pluggable SFP+ footprint
• Backward compatibility: Supports 1000Base-T/2.5GBase-T/5GBase-T/10GBASE-T
• Low Power Consumption (2.3W @ 30m)
• Auto-negotiates with other 10GBase-T PHYs
• Provides Low-cost solution for copper network edge applications
• RJ-45 connector
• Operating case temperature range of 0°C to +70°C

Application

• 10 Gigabit Ethernet over Cat 6A/7 cable
• 5 Gigabit Ethernet over Cat 6A/7 cable
• 2.5 Gigabit Ethernet over Cat 6A/7 cable
• 1.25 Gigabit Ethernet over Cat 5e cable

Pin Definitions

Pin Descriptions

Note:

Plug Seq.: Pin engagement sequence during hot plugging.

      1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

    3. LOS is open collector output. Should be pulled up with 4.7k~10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

    4. RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES.

    5. TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.

Compatibility

Each Gigaopto’s optical transceiver is tested in the host device to verify interoperability, and we promise 100% full compatibility on the specified device with a 3-year warranty. For this GTS-T0096-03 SFP+ T copper optical transceiver module, please refer to the P/N correspondence table. If you are interested in knowing more compatibility, you are always welcome to contact us.

Mechanical Specifications (Unit:mm)